Tire Replacement and Rotation

Tires are critical to your cars performance and safety. Worn tires can be extremely dangerous to you and everyone around you, especially in slippery conditions. They comprise traction on slick pavement and can greatly increase braking distance. Improperly inflated tires can wreak havoc on your gas mileage.

Here at International Auto Repair, we can make sure your you get the right tires on your car and get the most life out of them. This comes through proper balancing, rotation, and replacement. Tires should be rotated front to back every 6,000 miles for best results and maximum life out of them.

To keep your tires wearing even we recommend keeping your car in proper alignment. We both two wheel and four wheel alignment services.

We carry large variety of tire styles and sizes from many manufacturers.

Causes of Excessive Tire Wear

  • Uneven or accelerated tire wear can be caused by wheel misalignment, worn suspension and steering components, and/or improper tire inflation.
  • The most critical alignment angle with respect to tire wear is toe. Camber is also important and can be
  • affected by caster. Misalignment is usually caused by worn, loose or bent suspension and steering parts (bad tie rod ends, idler arms, control arm bushings, ball joints, struts, etc), but can also be due to spring sag or improper ride height.
  • With tire inflation, underinflation is just as bad as overinflation. Both cause uneven tire wear. Underinflation can also make a tire run dangerously hot.
  • For a tire to roll down the road with the least amount of resistance and maximum directional stability, it must be aligned with the road, parallel to the other three wheels on the vehicle, square with the chassis, and properly inflated.
  • Rolling resistance is affected by a number of things, one of which is the straightness of the tire with respect to the direction of travel. If the tire is skewed slightly to one or the other (toed in or out), it will scrub as it rolls. Scrub increases rolling resistance and also wears away the tread, leaving a feathered wear pattern.
  • Toe refers to the parallelism of a front or rear wheel to its companion on the opposite side. From a bird’s-eye view, all four wheels should be parallel to one another and pointing straight ahead.
  • Toe is measured by comparing the distance between the front edges of both tires on an axle to the distance between the trailing edges. If the distance between the front edge is further apart than that at the rear, wheels have toe-out.
  • If front is closer together than the rear, wheels have toe-in. Toe setting may be specified in inches, millimeters or degrees. Toe is most affected by worn tie rod ends, a worn or loose idler arm or center link, or a bent steering arm.
  • To minimize tire wear, rolling toe should be kept as near zero as possible. To achieve this, the compliance or amount of give in the vehicle’s steering linkage and suspension must be taken into consideration.
  • As a vehicle starts to move, rolling resistance pushes the tires back. This compresses the couplings and rubber fittings in the steering linkage and causes the wheels to toe-out slightly. It isn’t much of a change, but most rear wheel drive vehicles call for static toe-in settings of around 1/16” to1/8 to compensate.
  • With front-wheel drive, the situation is different because the front wheels pull the vehicle down the road.
  • Engine torque causes the wheels to toe-in under load. Most FWD suspensions have a negative scrub radius built into the steering geometry.
  • The tire pivots slightly to the outside of its centerline. This helps to offset the tendency to toe-in. Even so, most front wheel drive vehicles still require toe settings of zero to 1/8” toe-out.
  • Toe also changes as the front wheels turn. Because the inner and outer wheels don’t follow the same path (the inner one follows a smaller circle than the outer one), the inner wheel must toe-out to compensate. This is called the “Ackerman Principle of Steering” after the engineer who invented the idea.
  • Toe-out depends on the angle of the steering arms with respect to the steering knuckles and chassis. The amount by which toe changes is called “toe-out on turns.” This angle is also listed in alignment specs and is checked by turning the wheels on the alignment rack.
  • If toe-out on turns is off because of a bent steering arm, the tires will squeal and scrub whenever the wheels are steered.
  • Camber also affects tire wear. For directional stability, the tires must be perpendicular (straight up and down) with respect to the road. Any tilt to the inside or outside will cause a tire to turn in that direction like a bicycle leaning into a turn. This causes steering to pull to one side and creates uneven wear across the tread face.
  • Camber is the inward or outward tilt of the wheels as viewed from either front or rear of the car. If wheels lean in, they have negative camber. If they lean out, they have positive camber.
  • The amount of camber is always expressed in degrees and is found by measuring the tilt of the wheels on an alignment rack or by using a level that attaches to the wheel.
  • Because camber affects tire wear, the idea situation is to have zero running camber on all four wheels to maintain full tread contract with the road. Like toe, camber changes as the suspension moves up and down. To keep the wheels vertical once the vehicle is loaded, a small amount of static positive camber may be required.
  • Camber should generally be within ½ degree side-to-side. Otherwise, the vehicle will lean toward the side with the most positive camber.
  • Camber misalignment can be caused by sagging spring, a bent strut, bent spindle, worn control arm bushing, worn ball joint, or mislocated strut tower (too far in or out).
  • Camber corrections are made by replacing worn parts and/or by realigning the suspension using either the factory adjustments (cams, shims or elongated holes) or aftermarket aids.